DOI:
https://doi.org/10.69717/jaest.v5.i1.112Keywords:
Beetroots, Beta vulgaris L, Drying process, Moisture ratio, Oven dryer, Forced convectionAbstract
Removal of moisture from food is popularly called drying and it is one of the most vital preservation techniques used in the food industry. In this study, the beetroots (Beta vulgaris L.) were dried in a laboratory oven dryer. The samples of fresh beetroots were dehydrated under a temperature of 50°C. The experimental study selected three different forms of the product, we choose a square form with (5 × 5 cm) and thickness e = 5 mm, a semi-circle form with thickness e = 5 mm and diameter D = 5 mm, and a triangle form with (5 × 5 × 5 cm) and thickness e = 4 mm. The main objective of the present study is to find the selection of the drying techniques essential to producing high-quality dried products in a rational time. The results give the moisture ratio of the different forms of the beetroot product as a function of time drying, while the triangle form responded to the drying process faster than the other two forms.
Downloads
Published
Issue
Section
License
Copyright (c) 2025 Journal of Applied Engineering Science & Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Amar Rouag, Adel Benchabane, Adnane Labed, Nora Boultif, Thermal design of air cooled condenser of a solar adsorption refrigerator , Journal of Applied Engineering Science & Technology: Vol. 2 No. 1 (2016): JAEST
- Toufik Arrif1, Adel Benchabane, Abdelmadjid Chehhat, Abdelfetah Belaid, Amar Rouag, Numerical simulation of convective heat losses in a helical tube of a cylindrical solar receiver , Journal of Applied Engineering Science & Technology: Vol. 4 No. 2 (2018): JAEST
- Loubna Ben Amor, Ahmed Boutarfaia, Omar Bentouila, Effects of Zr/Ti ratio and sintering temperature on Structural and electrical properties of PFN-PNN-PZTceramics near the morphotropic phase boundary , Journal of Applied Engineering Science & Technology: Vol. 4 No. 1 (2018): JAEST
- Miloud Zellouf, Noureddine Moummi, Adnane Labed, Kamel Aoues, Multiple solutions for flow mode−transition in an inclined cavity generated by natural convection , Journal of Applied Engineering Science & Technology: Vol. 2 No. 2 (2016): JAEST
- Issam Abdesslam, Mekki Mellas, Pushover analysis of the reinforced concrete frames with soft first storey using a fiber hinge model , Journal of Applied Engineering Science & Technology: Vol. 3 No. 2 (2017): JAEST
- Mohamed-Amine Khadraoui, Leila Sriti, Study and optimization of the windows’ impact on thermal comfort and energy efficiency (Case of offices in a hot and arid climate) , Journal of Applied Engineering Science & Technology: Vol. 4 No. 1 (2018): JAEST
- Sabiha Aklouche‐Benouaguef, Belkacem Zeghmati, Bifurcations in two‐dimensional differentially heated cavity , Journal of Applied Engineering Science & Technology: Vol. 3 No. 1 (2017): JAEST
- Charafeddine Beldjani, Kamel Aoues, Noureddine Belghar, Yousra Boutera, Mohamed Aymen Kethiri, CFD Analysis of Hybrid Photovoltaic Thermal (PV/Th) Solar Collector Efficiency Incorporating Ag-AL2O3/water Hybrid Nanofluids , Journal of Applied Engineering Science & Technology: Vol. 5 No. 1 (2025): JAEST
- Djamel Taibi, Stability analysis of the extended Kalman filter for Permanent Magnet Synchronous Motor , Journal of Applied Engineering Science & Technology: Vol. 1 No. 2 (2015): JAEST
- Pierre Delage, Hamza Menaceur, Malik Belmokhtar, Jean Talandier, Effect of a partial saturation on the hydromechanical response of a clay rock , Journal of Applied Engineering Science & Technology: Vol. 2 No. 1 (2016): JAEST
You may also start an advanced similarity search for this article.